Activity Stream
-
Older Activity
-
Today, 07:17 AMLMagelitz replied to a thread Trying to get trailer camera wire fished through to the Pin Box in ElectronicsIt’s not that bad. You can fish along part of the frame and not take down the entire edge of the coroplast. I went up the ladder as well, and over...4 replies | 109 view(s)
-
Today, 07:11 AMI just had 235/80R16 Westlake tires replaced with Sailun S637 tires. Never had any issues with the Westlakes, although a G rated tire. If available I...64 replies | 45172 view(s)
-
Today, 07:06 AMJohnww replied to a thread Trying to get trailer camera wire fished through to the Pin Box in ElectronicsI used a wire fish to run the wires for my disc brake project. I removed the small screws the held up the exterior cover along the path of the wire...4 replies | 109 view(s)
-
Today, 06:55 AMThanks for the reply, hopefully won’t have too much time in it18 replies | 15082 view(s)
-
Today, 06:46 AMI drilled a new hole back a few inches from the pin. That got me into an open chamber that goes to the front basement. Then I ran a wire backward...18 replies | 15082 view(s)
-
Today, 06:34 AMFonecop1 replied to a thread Trying to get trailer camera wire fished through to the Pin Box in ElectronicsThat explains why my fish steel didn’t want to go anywhere. I was planning to use 1/2 inch cable clamps and attach the cable to the outside using the...4 replies | 109 view(s)
-
Today, 06:33 AMI bought the fixed 55 psi regulator advertised as high flow. Tired of changing out the adjustable ones about every year or so.16 replies | 3078 view(s)
-
Today, 05:22 AMWhittleBurner replied to a thread Which brand/website did you buy your trailer cover from? in General DiscussionThis is the 1st I have heard of carcovers website so chances are you won't find many that have had experience using them here1 replies | 125 view(s)
-
Today, 05:16 AMWhittleBurner replied to a thread New Memeber and owner of Grand Design 303 in Welcome Mat | New Member IntroductionsHi and Welcome to the 303 club! we spend winters in our 303 on the west coast of Fl. Very comfortable for 7 mos, We're still there! Enjoy1 replies | 46 view(s)
-
Today, 04:41 AMDaveInTN replied to a thread New Member with hopes to get our dream GD soon! in Welcome Mat | New Member IntroductionsGood luck in your search! I see one listed on RVTrader in Slinger, WI if that’s anywhere near you (your profile lists WI as your state).2 replies | 78 view(s)
-
Today, 03:52 AMJerry Davis started a thread New Memeber and owner of Grand Design 303 in Welcome Mat | New Member IntroductionsHi Just purchased a 2024 Grand Design 303 RLS on Thursday. My wife and I are looking forward to traveling and spending some winter months in...1 replies | 46 view(s)
-
Yesterday, 10:01 PMLMagelitz replied to a thread Trying to get trailer camera wire fished through to the Pin Box in ElectronicsThe hole that the existing trailer wiring goes thru extends up into the front cap. Our washer/dryer is in the middle in our rig, and we have a...4 replies | 109 view(s)
-
Yesterday, 08:53 PMNew England Weekender started a thread Which brand/website did you buy your trailer cover from? in General DiscussionAssuming you own one. Just found carcovers.com. 24'-27' cover for $289 with another 20% off. Lifetime warranty too. Are these covers legit or is...1 replies | 125 view(s)
-
Yesterday, 08:48 PMFonecop1 started a thread Trying to get trailer camera wire fished through to the Pin Box in ElectronicsDoes anybody have any tips or tricks to getting a wire fished from the pin box existing hole to the front storage compartment? I have the GM camera...4 replies | 109 view(s)
-
Yesterday, 08:22 PMUnsure of your exact meaning. Are you saying the key is not unique to that lockset? That a person with a different lockset, but the same brand could...9 replies | 439 view(s)
-
Yesterday, 08:20 PMThe main reason I went to an adjustable regulator is that I had read they allowed increased flow at the same set pressure as the non-adjustable...16 replies | 3078 view(s)
-
Yesterday, 08:05 PMI'm new. I was trying to reply to jkwilson and trailrydr7 replies | 141 view(s)
-
Yesterday, 08:04 PMThank you.7 replies | 141 view(s)
-
Yesterday, 08:02 PMThat did the trick! Thank you so much. Have a great weekend.7 replies | 141 view(s)
-
Yesterday, 07:59 PMAll my 2019 295RL exterior trim screws are square #2's also. You want to not over torque them... easy to strip out the threaded holes.7 replies | 141 view(s)
-
Yesterday, 07:55 PMtrailrydr replied to a thread Rust prevention on rotors over winter? in Axles, Brakes, and SuspensionYeah.... the "surface" should wear off. Any deeper pitting may not clean as well. Small pitting wont effect the performance of the braking system. ...6 replies | 177 view(s)
-
Yesterday, 07:54 PMThat's pretty much what I added to my trailer. The handle is right there, so I can easily see that it is closed before removing the cap. Makes for...21 replies | 41680 view(s)
-
Yesterday, 07:39 PMIt is. Two square heads rotated 1/8 turn from each other for assembly speed. Try the #27 replies | 141 view(s)
-
Yesterday, 07:39 PMThank you. I tried but the website is unresponsive.2 replies | 93 view(s)
-
Yesterday, 07:29 PMYou can sign up for the GDRV site https://www.granddesignrv.com/owners/mygdrv ,from there you can search part for your particular trailer and also...2 replies | 93 view(s)
-
Yesterday, 07:29 PMAny pointers on how you fished tha cake out at the pin box? I tried maneuvering an about 3/16 stiff piece of fish steel starting at the existing hole...18 replies | 15082 view(s)
-
Yesterday, 07:18 PMRazenLori - This is the gate valve we're talking about: ...21 replies | 41680 view(s)
-
Yesterday, 07:10 PMI wish my square heads.7 replies | 141 view(s)
-
Yesterday, 07:07 PMWhittleBurner replied to a thread New Member with hopes to get our dream GD soon! in Welcome Mat | New Member IntroductionsWelcome and good luck on your hunt!2 replies | 78 view(s)
-
Yesterday, 07:06 PMAll of mine are #2 square head!7 replies | 141 view(s)
Challenge with GM Rear Trailer...
Today, 06:46 AM in Electronics