User Tag List

Page 4 of 4 FirstFirst ... 234
Results 31 to 33 of 33
  1. #31
    Site Sponsor orbiker's Avatar
    Join Date
    Oct 2015
    Location
    Springfield, Oregon
    Posts
    2,328
    Mentioned
    17 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by orbiker View Post
    So Chris;
    The little screw on the blue pod are for the adjustment.

    Does it take much of a turn and do you do the adjustment with power on?

    Thanks, KEN
    Quote Originally Posted by CoChris View Post
    OK. I am a little slow. It is "pot", not "pod". Short for Potentiometer. A type of variable resistor. Yes, the little screw onthe side (end pointing up in the picture) is the adjustment. If I remember correctly, they are ten turn pots, but it takes very little turn to adjust the voltage.

    You are working with live, 120v power for the adjustment. If you are not experienced and/or comfortable around dangerous voltage, I would NOT recommend you adjust them yourself. I hooked up the remote display (so I could see the voltage reading) and the input to line (120v) power (I used the same input to both legs), and I hooked up a good (known accurate) voltmeter across the inputs. I then adjusted each pot until the display for each legs voltage read the same as my meter. Again, remember you are working around live power with a lot of exposed terminal. Be very careful if you do this yourself.

    Chris
    Quote Originally Posted by gbkims View Post
    Yes the screws on the blue pots. One is L1, the other is L2.
    Yes, power on. Turn a bit and let the remote display update, then adjust till you match your DMM voltage reading.
    Thanks
    I can handle that.
    I fix coin washers and dryers for a living. I don't remember the last time I unplugged the machines to fix them. 99 % of the time it's harder to get to the plug, then just fixing the problem.
    KEN
    Backpacker and tent camper all my life, including BSA as a kid and adult.
    Motorcycle trips across the USA with a tent - 1978 to Present.
    02-10-2005 - 2002 F350 SWD PSD and 2003 Citation 10'8S mostly for Crater Lake Ski Patrol.
    10-29-2015 - 2016 Grand Design 380TH. It's HUGE compared to a camper.
    10-19-2018 - traded truck for a 2016 Ram 3500 DRW Laramie CC 4 X 4 Long Box.
    03-16-2019 - Traded Momentum for a New 2018 374TH-R Solitude
    FULL TIME RV'er Nov 2021

  2. #32
    Site Sponsor
    Join Date
    Apr 2017
    Location
    Fort Collins, Colorado
    Posts
    1,303
    Mentioned
    25 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by orbiker View Post
    Thanks
    I can handle that.
    I fix coin washers and dryers for a living. I don't remember the last time I unplugged the machines to fix them. 99 % of the time it's harder to get to the plug, then just fixing the problem.
    KEN
    You should have no problem making the adjustment(s). As you zero in on the correct setting (adjustment) let the display cycle through the readings a couple of times to make sure the reading is stable before buttoning it all back up.

    Chris
    Chris & Karen
    Fort Collins, CO
    2017 F-350 SRW 6.7 Lariat Value CC LB 4x4
    2018 Solitude 310GK - Sold 7/2023

  3. #33
    Site Sponsor orbiker's Avatar
    Join Date
    Oct 2015
    Location
    Springfield, Oregon
    Posts
    2,328
    Mentioned
    17 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by CoChris View Post
    You should have no problem making the adjustment(s). As you zero in on the correct setting (adjustment) let the display cycle through the readings a couple of times to make sure the reading is stable before buttoning it all back up.

    Chris
    DONE

    That was easy, with the great instructions. Thanks, KEN
    Backpacker and tent camper all my life, including BSA as a kid and adult.
    Motorcycle trips across the USA with a tent - 1978 to Present.
    02-10-2005 - 2002 F350 SWD PSD and 2003 Citation 10'8S mostly for Crater Lake Ski Patrol.
    10-29-2015 - 2016 Grand Design 380TH. It's HUGE compared to a camper.
    10-19-2018 - traded truck for a 2016 Ram 3500 DRW Laramie CC 4 X 4 Long Box.
    03-16-2019 - Traded Momentum for a New 2018 374TH-R Solitude
    FULL TIME RV'er Nov 2021

Page 4 of 4 FirstFirst ... 234

Similar Threads

  1. Progressive industries HW50c Instal 377 MBS
    By Hwktlg8 in forum Mods and DIY
    Replies: 10
    Last Post: 03-03-2017, 08:08 PM
  2. Install PI EMS HW50C - good location in 397TH?
    By VentureRider in forum Electrical System and Wiring
    Replies: 0
    Last Post: 08-17-2016, 05:37 PM
  3. Added a Progressive Industries EMS-HW50C
    By GD350M in forum Electrical System and Wiring
    Replies: 1
    Last Post: 12-24-2014, 11:44 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

DISCLAIMER:This website is not affiliated with or endorsed by Grand Design RV, LLC or any of its affiliates. This is an independent site.