User Tag List
Results 61 to 66 of 66
Thread: Extra visibility added
-
03-31-2019, 06:02 PM #61
See this thread for how Tom @GENESIS ran the wires inside the corner moldings . . .
https://www.mygrandrv.com/fo...ad-again/page5
RobCate & Rob
2015 Reflection 303RLS
-
03-31-2019, 06:49 PM #62
- Join Date
- Jul 2018
- Location
- Fla. via NY
- Posts
- 131
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I see. You might be able to drill a hole where the light will go and push a fish tape down to where the existing lights are and pull the wires back up through. The only thing is once you drill the hole it's there. Let us know how it goes.
-
11-02-2019, 11:23 AM #63
- Join Date
- Sep 2019
- Posts
- 4
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Anyone have a picture of the bottom hole that was drilled out. Trying to get a picture of the area to drill the correct spot. thanks
-
05-11-2023, 11:21 AM #64
- Join Date
- May 2023
- Location
- NW Arkansas
- Posts
- 3
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I used 2 LED Truck Tailgate Light Bar Strip, 3 Row 60 Inch Waterproof Red White Reverse, Brake Lights, Turn Signal and Running Light. 3M adhesion. Routed the wiring through the corner trim and tied into each tail light. had to run a wire for the reverse light.https://1drv.ms/v/s!AhuP9SJ2YX3vg_cs...Z1HBA?e=5mqw3d
-
05-13-2023, 05:59 AM #65
- Join Date
- May 2023
- Location
- Ontario,Canada
- Posts
- 2
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Great info by all. Thanks. Purchased a 15” LED strip to install on back of 2022 Reflection 260 RD for turning and braking visibility when travelling with bikes. Would like to install on each side next to window (vertically)and run wires down to connect to existing lights but unsure of drilling into framing. First thought is to use stud finder. Any suggestions would be appreciated.
-
05-14-2023, 02:35 PM #66
- Join Date
- May 2023
- Location
- NW Arkansas
- Posts
- 3
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Can you see my turn signal now?
I used these DOT approved tailgate bars that are 60 inches. They use 3M adhesion tape. I cut the plug off and spliced the turn lights together. I routed the wires under the corner trim and under the back were I just connected to the tail light. I noticed a big difference when moving in traffic now.
https://youtube.com/shorts/EI1W1CGCqck
Derick, Becky & a Pup named Willy
2015 Duramax 3500HD High Country CC 4x4 Dually B&W Turnover Ball Hitch
2016 Grand Design Momentum 388M Reese 20K Goosebox
Similar Threads
-
Truck mod: adding extra gas tanks
By wrp75_CO in forum Mods and DIYReplies: 21Last Post: 04-30-2016, 05:18 PM -
Extra Battery Cutoff Switch
By Phansen404 in forum Electrical System and WiringReplies: 4Last Post: 02-01-2016, 06:04 PM -
Solution for extra step on the front entrance door?????
By louisb in forum General DiscussionReplies: 5Last Post: 09-09-2015, 06:17 PM -
Extra Table set and Couch for 380
By Allang17 in forum General DiscussionReplies: 0Last Post: 10-30-2014, 07:05 AM
Check those tires!
Today, 03:33 PM in Tires